1、细啄面花岗石饰面板装置办法
1. Method of Fine-pecking Granite Decorative Panel Device
细啄面花岗石饰面板有剁斧板、机刨板和粗磨板等品种，其板厚普通为50mm、76mm、100mm，墙面、柱面多用板厚50mm，勒脚饰面多用76mm、100mm。
Fine pecking face granite decorative panels have chopping axe board, planer board and rough grinding board. The thickness of the panels is 50 mm, 76mm and 100 mm. The thickness of the wall and column panels is 50 mm, and the length of the legs is 76mm and 100 mm.
1)板材启齿方式
1) Sheet metal teeth opening method
细啄面花岗石饰面板装置。普通经过镀锌钢锚固件与基体衔接锚固，锚固件有扁条锚件、圆杆锚件和线形锚件等，因而依据其采用的锚固件的不同，所采用的板材开方式也各不相同，饰面板角位的接缝宽度及阳角交接方式
Fine pecking granite facing panel device. Ordinary galvanized steel anchors are connected with the base, and the anchors include flat bar anchors, round bar anchors and linear anchors. Therefore, according to the different anchors used, the plate opening modes are different, the joint width and positive angle joint modes at the corner of the decorative panel are also different.
2)锚固办法
2) Anchorage Method
用镀锌钢锚固件将饰面板版面与基体锚固后，缝中分层灌注1:2.5水泥砂浆，扁条锚固件的厚度为3mm、5mm、6mm，宽25mm、30mm，其锚固方式
After anchoring the veneer plate and the base with galvanized steel anchors, 1:2.5 cement mortar is poured into the cracks. The thickness of flat bar anchors is 3 mm, 5 mm, 6 mm, and the width is 25 mm and 30 mm.
2、镜面花岗石饰面板装置办法
2. Installation Method of Mirror Granite Decorative Panel
基面花岗石饰面板的装置可采用挂贴式,树脂胶粘结式、楔固式、钢网式等装置办法停止,其工艺和施工工序与前述大理石镜面饰面板的办法相同,近来镜面花岗石面板的装置常采用干挂法工艺,干挂工艺有两种办法。
The installation of base granite panel can be stopped by hanging and pasting, resin bonding, wedge-bonding and steel mesh. Its process and construction procedure are the same as those of the marble mirror panel. Recently, the installation of mirror granite panel often adopts dry hanging process. There are two methods of dry hanging process.
1)直接挂板式
1) Direct hanging plate type
直接挂板式装置板块，是用不锈钢角将板块支托在墙面上，不锈钢角用收缩螺栓固定在墙面上，上下两层不锈钢角的间距鞥与板块的高度，该装置方式的关键工艺就是不锈钢角装置尺寸的精确和板块上凹槽位置的精确，板块上是个凹槽位应在板厚中心线上，并在距板侧边40mm处，不锈钢角的散布，其与板块的装置
The plate of the direct hanging plate device is supported on the wall surface by stainless steel angle, and the stainless steel angle is fixed on the wall surface by shrinking bolts. The spacing between the upper and lower stainless steel angles and the height of the plate is the key technology of the device. The key technology of the device is the accuracy of the size of the stainless steel angle device and the position of the groove on the plate. The groove on the plate should be located on the center line of the plate thickness and at the distance. Distribution of stainless steel angle at 40 mm side of plate and its device with plate
装置时从底层开端，如今空中墙边外的板块下，摊铺一条宽于板块与墙面之间间隔的水泥浆，然后再向不锈钢角上装置板块，在装置第二层板块前，先在层板顶端抹5mm厚的素水泥，并请求有一定稠度，以不流淌为准，这种装置花岗石板块的办法，普通用于墙面高度小于5m的花岗石墙面。
Starting from the bottom, under the plate outside the wall in the air, a cement slurry is paved which is wider than the interval between the plate and the wall, and then the plate is installed on the stainless steel corner. Before installing the second plate, plain cement 5 m thick is first applied on the top of the first plate, and a certain consistency is requested, whichever is not flowing. This method of installing granite plate is commonly used on the wall. Granite wall with height less than 5 m.
2)花岗石预制板干挂
2) Dry hanging of granite prefabricated slabs
该办法是把钢筋细石混凝土与磨光花岗石预制成复合板，并在浇筑成型前参加预埋件，使其衔接成一体，然后再用不锈钢角停止干挂，或者用专用衔接用具与墙面干挂。
The method is to make composite slabs of reinforced fine stone concrete and polished granite, and join embedded parts before pouring and forming, so that they can be integrated, and then stop dry hanging with stainless steel angle, or dry hanging with special linking tools and walls.
I believe that after reading this article's introduction of Jinan office decoration http://www.saiyunzs.com, I will have my own understanding of this aspect, and other problems can be solved well in the future.
